Lattice strain accommodation and absence of pre-transition phases in Ni50Mn25+xIn25-x.

The stoichiometric Ni50Mn25In25Heusler alloy transforms from a stable ferromagnetic austenitic ground state to an incommensurate modulated martensitic ground state with a progressive replacement of In with Mn without any pre-transition phases. The absence of pre-transition phases like strain glass in Ni50Mn25+xIn25-xalloys is explained to be the ability of the ferromagnetic cubic structure to accommodate the lattice strain caused by atomic size differences of In and Mn atoms. Beyond the critical value ofx= 8.75, the alloys undergo martensitic transformation despite the formation of ferromagnetic and antiferromagnetic clusters and the appearance of a super spin glass state.

MOKE setup exploiting a nematic liquid crystal modulator.

Here we report on the magneto-optical Kerr effect employing a nematic liquid crystal (LC) device as an optical modulator. This device allows performing intensity, phase, and polarization modulated measurements with a huge signal-to-noise ratio when compared to those obtained by means of an opto-mechanical chopper and a photo-elastic modulator. The results demonstrate that the optimal performance is achieved modulating the polarization state of the incident light by means of the LCs.

Functionalization of carbon fiber tows with ZnO nanorods for stress sensor integration in smart composite materials.

The physical and operating principle of a stress sensor, based on two crossing carbon fibers functionalized with ZnO nanorod-shaped nanostructures, was recently demonstrated. The functionalization process has been here extended to tows made of one thousand fibers, like those commonly used in industrial processing, to prove the idea that the same working principle can be exploited in the creation of smart sensing carbon fiber composites. A stress-sensing device made of two functionalized tows, fixed with epoxy resin and crossing like in a typical carbon fiber texture, was successfully tested. Piezoelectric properties of single nanorods, as well as those of the test device, were measured and discussed.

Influence of the transition width on the magnetocaloric effect across the magnetostructural transition of Heusler alloys.

We report a complete structural and magneto-thermodynamic characterization of four samples of the Heusler alloy Ni-Co-Mn-Ga-In, characterized by similar compositions, critical temperatures and high inverse magnetocaloric effect across their metamagnetic transformation, but different transition widths. The object of this study is precisely the sharpness of the martensitic transformation, which plays a key role in the effective use of materials and which has its origin in both intrinsic and extrinsic effects. The influence of the transition width on the magnetocaloric properties has been evaluated by exploiting a phenomenological model of the transformation built through geometrical considerations on the entropy versus temperature curves. A clear result is that a large temperature span of the transformation is unfavourable to the magnetocaloric performance of a material, reducing both isothermal entropy change and adiabatic temperature change obtainable in a given magnetic field and increasing the value of the maximum field needed to fully induce the transformation. The model, which is based on standard magnetometric and conventional calorimetric measurements, turns out to be a convenient tool for the determination of the optimum values of transformation temperature span in a trade-off between sheer performance and amplitude of the operating range of a material.This article is part of the themed issue 'Taking the temperature of phase transitions in cool materials'.

Non-contact direct measurement of the magnetocaloric effect in thin samples.

An experimental setup, based on a non-contact temperature sensor, is proposed to directly measure the magnetocaloric effect of samples few micrometers thick. The measurement of the adiabatic temperature change of foils and ribbons is fundamental to design innovative devices based on magnetocaloric thin materials or micro-structuring bulk samples. The reliability of the proposed setup is demonstrated by comparing the measurements performed on a bulk gadolinium sample with the results obtained by an experimental setup based on a Cernox bare chip thermoresistance and by in-field differential scanning calorimetry. We show that this technique can measure the adiabatic temperature variation on gadolinium sheets as thin as 27 µm. Heat transfer simulations are added to describe the capability of the presented technique.

Direct magnetocaloric characterization and simulation of thermomagnetic cycles.

An experimental setup for the direct measurement of the magnetocaloric effect capable of simulating high frequency magnetothermal cycles on laboratory-scale samples is described. The study of the magnetocaloric properties of working materials under operative conditions is fundamental for the development of innovative devices. Frequency and time dependent characterization can provide essential information on intrinsic features such as magnetic field induced fatigue in materials undergoing first order magnetic phase transitions. A full characterization of the adiabatic temperature change performed for a sample of Gadolinium across its Curie transition shows the good agreement between our results and literature data and in-field differential scanning calorimetry.